室内隔音墙怎样装效果最佳，请问墙面装修怎么

　　室内隔音墙怎样装效果最佳，请问墙面装修怎么做隔音？

　　最近有很多热心网友都十分关心室内隔音墙怎样装效果最佳，请问墙面装修怎么做隔音？这个问题。还有一部分人想了解室内隔音墙怎样装效果最佳。对此，和记百科小编「陌路荒年」收集了相关的教程，希望能给你带来帮助。

　　

墙面装修怎么做隔音

 

　　1、确认安装位置：先在墙面上测量所需要动工的尺寸，找好安装点，根据安装的尺寸和位置确定水平线和垂直线，还要确定好电线的插口、管子的位置等，预留好足够的空间。

　　2、剪裁吸音板：按照现场的实际尺寸计算需要裁剪的吸音板尺寸，并裁剪好吸音板。要注意对立面上是否有对称要求，尤其要注意裁开部分吸音板的尺寸，保证两边的对称。

　　3、安装吸音板：吸音板的安装顺序，遵循从左到右、从下到上的原则。吸音板横向安装时，凹口朝上；竖直安装时，凹口在右侧。部分实木吸音板有对花纹要求的，每一立面应按照吸音板上事先编制好的编号依次从小到大进行安装。

　　4、固定吸音板：用射钉安装木龙骨，将吸音板固定在龙骨上，射钉必须有三分之二以上嵌入木龙骨，而且要均匀排布，并要求有一定的密度，每块吸音板与每条龙骨上联结射钉数量不能少于10个。

　　5、检修孔和其他问题：如检修孔的位置和吸音板施工墙面垂直接触，应要求更改检修孔的位置，保证吸音板的施工条件。

　　

室内隔音墙怎样装效果最佳

 

　　1、湿作业方法。用小砖砌墙，然后用水泥粉刷墙面，这种墙面隔音效果。另外，用纱网订在墙面，然后用水泥在墙面贴砖，这种隔音效果也是很好的。

　　2、干作业方法。在墙体内加一层泡沫板，然后处理墙面，这种效果一定要将泡沫板订严实，负责也会漏音，达不到隔音效果的。也可以在墙体内加一层隔音布，这种效果施工简便，而且隔音效果非常好。

　　

　　【英文介绍/For English】：

　　

　　1. Confirm the installation position: first measure the size of the required construction on the wall, find the installation point, determine the horizontal and vertical lines according to the size and position of the installation, and determine the socket of the wire, the position of the pipe, etc., reserve Good enough space.

　　2. Cut the sound-absorbing board: Calculate the size of the sound-absorbing board to be cut according to the actual size of the site, and cut the sound-absorbing board. Pay attention to whether there are symmetrical requirements on the opposite side, especially pay attention to the size of the cut part of the sound-absorbing panels to ensure the symmetry on both sides.

　　3. Install sound-absorbing panels: The installation sequence of sound-absorbing panels follows the principle of left to right and bottom to top. When the sound-absorbing panel is installed horizontally, the notch is upward; when it is installed vertically, the notch is on the right side. Some solid wood sound-absorbing panels have requirements for patterns, and each facade should be installed in order from small to large according to the numbers prepared in advance on the sound-absorbing panels.

　　4. Fix the sound-absorbing board: Install the wooden keel with shooting nails, and fix the sound-absorbing board on the keel. More than two-thirds of the shooting nails must be embedded in the wooden keel, and they should be evenly arranged and required to have a certain density. The number of nails connecting the plate and each keel shall not be less than 10.

　　5. Access holes and other problems: If the position of the access hole is in vertical contact with the construction wall of the sound-absorbing panel, the position of the access hole should be changed as required to ensure the construction conditions of the sound-absorbing panel.